Ei Electronics RadioLINK Ei 407 Smoke Alarm User Manual

For use only with Ei Electronics Easi-fit Mains Powered Smoke & Heat Alarms. The Ei168RC RadioLINK Base must be installed by a qualified electrician. 1.1) Install each RadioLINK Base in the centre of the ceiling at least 0.30m from light fittings (as per the smoke/heat alarm instructions) and connect to nearest mains circuit (see page 3). 1.2 ... May 23, 2012 · Ei Electronics - Fire and Gas Detection - The Ei450 Alarm Controller - Ei450 Introduction Video. Testing the Alarm controller with Fire, Smoke and CO Alarm Systems. The Ei141RC Ionisation Smoke Alarm is a mains powered alarm with a 9V Alkaline battery back-up and contains a proven long life Ionisation smoke chamber. Different alarms sensors work best at detecting different types of fire and so should be sited in appropriate rooms throughout a property. Nov 12, 2012 · If the alarms are still on the ceiling with the batteries removed, the smoke alarms have to beep to remind you to add new batteries. If they still beep after new batteries are inserted your smoke alarms might be older than 10 years or your replacement batteries were flat. Ei recommends EverReady 522 or Duracell MN1604.

Get Ei Electronics Ei 405TY RADIO SMOKE ALARMS with WIRELESS INTERCONNECT INSTRUCTION LEAFLET. Get all Ei Electronics manuals!

The Smoke Alarm locator is recommended for systems with three or more Smoke / Heat Alarms as it helps quickly identify the unit in alarm and reduces the impact of nuisance alarms. Pressing the Smoke Alarm Locator button will silence all interconnected alarms for 10 minutes, except those sensing fire. Jul 17, 2015 · Ei Electronics new AudioLINK feature is a means of extracting event data from the alarm to a specially design Smart Phone App. The phone application is specifically design to interpret the sound ... How to stop beeping from Ei / Aico mains powered smoke and heat alarms Ei141, Ei144, Ei146, Ei150, Ei151, Ei154, Ei156, Ei161, Ei164, Ei166. Here are some common questions we have been asked by our customers about Ei Electronics and Aico (Ei’s UK operation) mains powered smoke alarms and heat alarms through our fire safety forum. Get Ei Electronics Ei 405TY RADIO SMOKE ALARMS with WIRELESS INTERCONNECT INSTRUCTION LEAFLET. Get all Ei Electronics manuals! You'll be alarmed to hear that a number of smoke alarms we've tested don't work when exposed to fire and smoke. Read our smoke alarm reviews to learn the models you can trust and the ones you should avoid at all costs.

Fire Protection Shop: 0800 316 1469 - The Aico Ei407 Manual Call Point is an emergency device that when activated transmits a RadioLINK alarm signal. This alarm signal will cause all RadioLINK alarms in the system to sound and thereby warn occupants.

View and Download Ei Electronics Ei141RC - Ionisation user instructions online. Ei141RC - Ionisation Smoke Alarm pdf manual download. Also for: Ei146rc - optical, Ei144rc - heat, Ei161rc - ionisation, Ei164rc - heat, Ei166rc - optical. Download 160 Ei electronics Smoke Alarm PDF manuals. User manuals, Ei electronics Smoke alarm Operating guides and Service manuals. The Ei262 will transmit an RF alarm signal when it detects potentially dangerous levels of CO. This RadioLINK Alarm signal can be used to: 1. Wirelessly interconnect to other Ei Electronics RadioLINK Smoke/Heat Alarm devices (e.g. Smoke/Heat Alarms mounted on Ei168RC RadioLINK bases), so that all... View online User instructions for Ei Electronics Ei411H Remote Control or simply click Download button to examine the Ei Electronics Ei411H guidelines offline on your desktop or laptop computer. View and Download Ei Electronics RadioLINK Relay Module Ei428 instruction manual online. RADIOLINK RELAY FOR USE WITH EI168, 405, 405TY & 3105RF. RadioLINK Relay Module Ei428 Relays pdf manual download. Ei Electronics Smoke Alarm Manuals. ... Alarm Ei 407. Ei Electronics Call Point User's Manual. ... Smoke Alarm Ei168. Ei Electronics RadioLINK Base Smoke & Heat ... (Smoke / Heat / Fire Alarm supplied separately) Note: At least one RadioLINK Smoke/Fire/Heat Alarm is required to make the Ei170RF Alarm operational.This is not supplied with the Ei170RF and must be obtained separately. Important: Read these instructions, together with those from the separate RadioLINK Smoke/Heat/Fire alarms and accessories ...

» Read more about: Q & A »

Heat alarms are used in kitchens and garages where smoke or mist may regularly be present. Available as battery or mains powered units. ...via RF or a hard wired interface via a special link cable between an Ei Electronics RadioLINK Alarm system and a Warden Call or telecare System.

CHARLES INDUSTRIES, 1 ANACONDA ELECTRONICS 1 ANACONDA ELECTRONICS 1... A MODUL CARD CLOCK CONTROLLER CARD QPC841C QSDI CARD ROM CARD ALARM UNIT SER.

Preferably the Smoke Alarms should be interconnected so as to give sufficient warning throughout the property. RadioLINK plug-in modules are ideal in this situation as the Smoke Alarms will then interconnect using Radio Frequency (RF) signals - so no wiring is required. Figure 1 illustrates where Smoke Alarms and Heat Alarms should be located in a Find the user manual you need for your home appliance products and more at ManualsOnline. ... Ei Electronics Ei156TL Smoke Alarm User Manual. Open as PDF The Alarm automatically monitors the battery every 40 seconds. If it is depleted it will give a short beep every 40 seconds. The Ei603RF must be interconnected to Ei Electronics battery operated smoke Alarms located along the escape routes to ensure sufficient warning is given to all the occupants.

Pressing on the Ei407 Manual Call Point (MCP) black spot causes all the RadioLINK Alarms to sound. This informs the occupants that the building must be evacuated. The Ei 407 MCP also provides a means to test the RadioLink alarms without having to reach up to the smoke alarms on the ceilings as it can be reset with the plastic key (supplied). RadioLINK is the solution. With RadioLINK, mains powered smoke alarms are interconnected by wireless signals rather than cabling. It's so much simpler, more convenient - and easier to change or extend as and when required. The use of radio interconnection in Grade D alarm systems means that it is now much easier to comply replacement smoke/heat alarm kit containing an OEM Ei Electronic alarm head. This replacement kit contains everything you need to easily, quickly and safely replace your mains powered, Ei Electronics / Aico smoke or heat alarm. Removing the Existing Alarm 1. Disconnect the mains power Warning! Before the existing alarm is removed, the mains power Fire Protection Shop: 0800 316 1469 - The Aico Ei407 Manual Call Point is an emergency device that when activated transmits a RadioLINK alarm signal. This alarm signal will cause all RadioLINK alarms in the system to sound and thereby warn occupants. Ei Electronics Smoke, Fire and Carbon Monoxide Alarms. Product Guide 2014. Ei140RC and Ei160RC series alarms Ei207 and Ei208 CO Alarms, Ei450 Alarm Controller.

The Ei407 is a manual call point that when pressed sounds all the RF Alarms interconnected in Product Description; Technical Specification; Instructions and Datasheet A RF system consists of Ei Electronics Smoke, Heat, CO Alarms and  The Ei 407 MCP also provides a means to test the RadioLink alarms without having to reach up to the smoke alarms on the ceilings as it can be reset with the  For use only with Ei Electronics Easi-fit Mains Powered Smoke & Heat Alarms. The The Ei168RC RadioLINK Base transmits a Radio Frequency (RF) alarm signal as Ei407 Manual Call Point and/or Ei411H Remote Control Switch). RadioLINK+ Module effectively replaces the Ei168RC RadioLINK Base. The primary function of the Ei100MRF is to wirelessly interconnect all Ei Electronics at this point (refer to the Installation section in the Alarm instruction manual). If a Optional Accessories: Ei407 Manual Call Point, Ei428 Relay Module ,Ei414 Fire /.